Calculadora de Escada para Deck

Como Usar Esta Calculadora

1. 1Measure the total rise in inches - this is the vertical distance from the ground to the top of the deck surface.
2. 2Enter the desired stair width in feet - 36 inches (3 feet) is the code minimum for residential decks.
3. 3Click Calculate to get the number of steps, stringer count, tread boards, and riser boards needed.
4. 4Use the total run to plan the landing area - stairs need clear space at the bottom equal to the stair width.

Sobre Este Material

Deck stairs connect the deck surface to the ground and are one of the most structurally critical and code-regulated elements of a deck. Building code strictly governs riser height, tread depth, stairway width, headroom, handrail requirements, and landing dimensions. The two standard approaches to deck stair construction are cut stringers and housed (routed) stringers. Cut stringers are the most common residential method - a 2x12 board is notched in a sawtooth pattern to support the treads and risers. Each cut removes material from the board, so the effective throat (remaining wood behind the cuts) must be at least 3.5 inches to maintain structural integrity. The IRC specifies a maximum riser height of 7-3/4 inches and a minimum tread depth of 10 inches. The ideal residential stair has a 7-inch rise and 11-inch run, which produces a comfortable 37-degree angle. All risers must be the same height, with a maximum 3/8-inch variation between any two risers in the same flight. This means you cannot simply divide the deck height by a convenient number - you must calculate the exact rise per step. Stringer spacing follows the same rules as joist spacing: 16 inches on center for standard loads. A 36-inch wide stair typically needs 3 stringers (one on each side plus one in the center). For stair widths over 36 inches, add a stringer for each additional 16 inches. Stringers must be made from pressure-treated lumber since they rest on or near the ground. Tread boards are typically two 5/4x6 or 2x6 deck boards per step, with a 1/4-inch gap between them and a 1-inch nosing overhang at the front. Riser boards are optional by code in many areas but recommended to prevent children from climbing through the stairs. When used, risers are typically 1x8 boards. Stair stringers must land on a concrete pad, footing, or compacted gravel base - never directly on soil. A 4-inch concrete pad at least 36 inches wide and 36 inches deep (from the bottom riser) provides a solid, code-compliant landing. The landing must be level and extend at least the width of the stairs in the direction of travel.

Dicas de Instalação

• •Use a framing square with stair gauges to mark consistent 7-inch rise and 11-inch run cuts on the stringer.
• •Cut stringers from 2x12 pressure-treated lumber - the remaining throat after cuts must be at least 3.5 inches.
• •Attach stringers to the deck frame with an approved stair stringer connector (Simpson LSC or similar), not just toenails.
• •Pour a concrete landing pad at the base of the stairs at least 4 inches thick and as wide as the stairway.
• •Test all steps with a level after installation - uneven risers are a tripping hazard and a code violation.

Erros Comuns a Evitar

• ⚠Uneven riser heights - code allows a maximum 3/8-inch variation between risers; inconsistent risers are the leading cause of stair falls.
• ⚠Using 2x10 lumber for stringers instead of 2x12 - after cutting, a 2x10 stringer does not have enough throat depth for structural safety.
• ⚠Not supporting the bottom of the stringers on a concrete pad - stringers resting on soil will rot and sink within 2 to 3 years.
• ⚠Omitting a center stringer on stairs wider than 36 inches - without center support, treads flex and bounce underfoot.
• ⚠Forgetting to account for the deck board thickness when calculating total rise - measure from the finished deck surface, not the joist tops.

Calculadoras Relacionadas