Calculadora de Guarda-Corpo para Deck

Como Usar Esta Calculadora

1. 1Measure the total perimeter of your deck in feet (add up all sides).
2. 2Enter the length of the side attached to the house - this side does not need railing.
3. 3Click Calculate to get post count, baluster count, and rail linear footage.
4. 4The calculator assumes standard 6-foot post spacing and 4-inch on-center baluster spacing.

Sobre Este Material

Deck railing is a critical safety feature required by building code on any deck surface 30 inches or more above grade (24 inches in some jurisdictions). The International Residential Code (IRC) specifies a minimum railing height of 36 inches for residential decks and 42 inches for commercial or multi-family structures. Railing systems consist of four main components: posts, top rail, bottom rail, and balusters (spindles). Posts are typically 4x4 pressure-treated lumber or aluminum, spaced no more than 6 feet apart (8 feet maximum in some codes). Posts must be securely bolted to the deck frame - never just screwed to the deck boards or fascia. Use 1/2-inch carriage bolts or approved post-mount hardware like Simpson DTT2Z tension ties. Balusters must be spaced so that a 4-inch sphere cannot pass between them. For standard 1.5-inch square balusters, this means roughly 4 inches on center. The IRC also requires that the gap between the deck surface and the bottom rail be less than 4 inches, and that no opening in the railing allows a 4-inch sphere to pass through at any point. Top and bottom rails are typically made from 2x4 pressure-treated lumber, composite rail kits, or aluminum extrusions. A 2x6 flat cap on top of the posts creates a comfortable drink rail. Most composite railing systems (Trex, TimberTech, Deckorators) come as kits with pre-cut balusters, rail sections, and post sleeves in 6-foot and 8-foot lengths. Wood railing materials cost $15 to $30 per linear foot installed. Composite railing systems run $30 to $60 per linear foot. Aluminum and cable railing systems range from $50 to $100 per linear foot. For a typical 12x16-foot deck (approximately 40 linear feet of railing after subtracting the house side), wood railing costs $600 to $1,200 and composite costs $1,200 to $2,400. Railing is one of the most common deck code violations. Inspectors frequently flag insufficient post attachment, excessive baluster spacing, below-minimum railing height, and gaps exceeding 4 inches between the deck surface and bottom rail.

Dicas de Instalação

• •Bolt railing posts through the rim joist or deck frame with 1/2-inch carriage bolts - never attach posts with screws or lag bolts alone.
• •Use a spacer jig (cut a 4-inch block of wood) to maintain consistent baluster spacing across all sections.
• •Pre-assemble railing sections on the ground - it is much easier and more accurate than building in place.
• •Install a 2x6 flat cap rail on top for a comfortable drink rail that guests will appreciate.
• •Notch posts around the rim joist for maximum strength rather than face-mounting them to the outside of the fascia.

Erros Comuns a Evitar

• ⚠Face-mounting posts with screws only - posts must be bolted through the rim joist or use approved post-mount hardware to resist outward force.
• ⚠Spacing balusters too far apart - code requires that a 4-inch sphere cannot pass through any opening in the railing.
• ⚠Making railing too short - 36 inches minimum from the deck surface to the top of the rail; measure from the deck boards, not the joist tops.
• ⚠Leaving more than 4 inches between the deck surface and the bottom rail - this gap allows small children to roll underneath.
• ⚠Using untreated lumber for railing posts - posts are exposed to weather on all sides and will rot in 3 to 5 years without treatment or sealing.

Calculadoras Relacionadas